Package Dimensions Part LTL-816EE-072A Lens Transp

Datasheets.org.uk - 100 Million Datasheets from 7500 Manufacturers.

Package Dimensions Part LTL-816EE-072A Lens Transp

Datasheet Thumbnail

Top Searches for this datasheet

power consumption. 3.2mm dome package with 5.0mm leads pitch Available tape without lead forming overall height available slim unit design Reliable rugged
Package Dimensions
Part
LTL-816EE-072A
Lens
Transparent
Source Color
Hi-Eff.Red
Notes: dimensions millimeters (inches). Tolerance ±0.25mm(.010") unless otherwise noted. Protruded resin under flange 1.0mm(.04") max. Lead spacing measured where leads emerge from package. Specifications subject change without notice. Part LTL-816EE-072A BNS-OD-C131/A4 Page
Absolute Maximum Ratings TA=25
Parameter Power Dissipation Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) Continuous Forward Current Derating Linear From Reverse Voltage Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [1.6mm(.063") From Body] Maximum Rating Seconds Unit
Part LTL-816EE-072A BNS-OD-C131/A4
Page
Electrical Optical Characteristics TA=25
Parameter Symbol Min. Typ. Max. Unit Test Condition 10mA Note Note (Fig.6) Measurement @Peak (Fig.1) Note
Luminous Intensity
21/2
Viewing Angle
Peak Emission Wavelength
Dominant Wavelength
Spectral Line Half-Width
Forward Voltage
20mA
Reverse Current
Capacitance
1MHz
Note: Luminous intensity measured with light sensor filter combination that approximates (Commission International L'Eclairage) eye-response curve. off-axis angle which luminous intensity half axial luminous intensity. dominant wavelength, derived from chromaticity diagram represents single wavelength which defines color device. guarantee should added ±15%.
Part LTL-816EE-072A BNS-OD-C131/A4
Page
Typical Electrical Optical Characteristics Curves
Ambient Temperature Unless Otherwise Noted)
Part LTL-816EE-072A BNS-OD-C131/A4
Page
Compatible with radial lead automatic insertion equipment. Most radial lead plastic lead lamps available packaged tape folding. (0.197") straight lead spacing available. *Foing packaging simplifies handling testing. Reel packing available removing suffx potion.
Package Dimensions
Specification
Item
Tape Feed Hole Diameter Component Lead Pitch Front Rear Deflection Feed Hole Bottom Component Feed Hole Overall Component Height Lead Length After Component Height Feed Hole Pitch Lead Location Center Component Location Total Tape Thickness Feed Hole Location Adhesive Tape Width Adhesive Tape Position Tape Width Part LTL-816EE-072A BNS-OD-C131/A4
Symbol
Minimum -24.5 29.75 12.4 3.15 5.05 -8.5 14.5 17.5 0.488 0.124 0.198 -0.334 0.571 0.689 Page inch 0.149 0.188 -0.964 1.171
Maximum 25.5 31.25 11.0 13.0 4.55 7.65 0.90 9.75 15.5 19.0 Inch 0.165 0.228 0.078 1.004 1.23 0.433 0.511 0.179 0.301 0.035 0.384 0.610 0.118 0.748
CAUTIONS
Application limitation
LEDs described here intended used ordinary electronic equipment (such office equipment, communication equipment household application.) Consult Liteon's sales advance information application which exceptional quality reliability required, particularly when failure malfunction LEDs directly jeopardize life health (such airplanes, automobiles, traffic control equipment, life support system safety devices).
Storage
After being shipped from Liteon LEDs should kept 30°C less 70%RH less. LEDs should used within months. They stored year sealed container with nitrogen atmosphere moisture absorbent material. Please avoid rapid transitions ambient temperature high humidity environments where condensation occur.
Cleaning
alcohol-based cleaning solvents such isopropyl alcohol clean LED.
Forming Mounting
When forming lead, leads should bent point least from base epoxy bulb. base leadframe fulcrum during forming. Lead forming must done before soldering normal temperature. When mounted through hole type lamp, avoid occurrence residual mechanical stress clinching figure shown here.
Soldering
When soldering, leave minimum clearance from resin soldering point. Dipping resin into solder must avoided. apply stress lead frame during soldering while high temperature. Recommended soldering condition Soldering iron Temperature Soldering time 300°C Max. sec. Max. (one time only) Wave soldering Pre-heat Pre-heat time Solder wave Soldering time 100°C Max. sec. Max. 260°C Max. sec. Max.
Drive Method
current operated device, therefore, requires some kind current limiting incorporated into drive circuit. This current limiting typically takes form current limiter resistor placed series with LED. Consider worst case voltage variations that could occur across current limiting resistor. forward current should allowed change more than desired value.
Circuit model
Circuit model
Recommended circuit. difference brightness between LEDs could found Vf-If characteristics Part LTL-816EE-072A BNS-OD-C131/A4 Page
(Electrostatic Discharge)
Static Electricity power surge will damage LED. conductive wrist band anti- electrostatic glove recommended when handling these LED. devices, equipment machinery must properly grounded.
Reliability Test
Classification Test Item Test Condition Duration Cycle Referance Standard
Endurance Test
Room Temp,
Room Temp. Operation Life
MIL-STD-750D:1026 (1995)
duty, Pulse Width =1.25
1000
MIL-STD-883D:1005 (1991) 7021:B-1 (1982)
MIL-STD-202F:107D (1980) Temperature Cycling 30mins 5mins 30mins 5mins
cycles
MIL-STD-750D:1051(1995) MIL-STD-883D:1010 (1991) 7021: A-4(1982)
Environmental Solder Test Resistance
MIL-STD-202F:210A(1980)
Solder temperature 260±
MIL-STD-750D:2031(1995) 7021: A-1(1982)
MIL-STD-202F:208D(1980)
Solderability
Solder temperature 230±
MIL-STD-750D:2026(1995) MIL-STD-883D:2003(1991) 7021: A-2(1982)
Others appearance specifications product modified improvement without notice.
Part LTL-816EE-072A BNS-OD-C131/A4
Page

Package Dimensions Part LTL-816EE-072A Lens Transp

Top Searches for this datasheet

Other recent searches