SCHS118A
|
|
|
Top Searches for this datasheet
CD74HC08M - CD74HC08M
SCHS118A - SCHS118A
CD54HC08, CD74HC08, CD54HCT08, CD74HCT08
August 1997 Revised 2003
High-Speed CMOS Logic Quad 2-Input Gate
Description
CD54HC08, CD54HCT08, CD74HC08, CD74HCT08 logic gates utilize silicon gate CMOS technology achieve operating speeds similar LSTTL gates with power consumption standard CMOS integrated circuits. devices have ability drive LSTTL loads. 74HCT logic family functionally compatible with standard 74LS logic family.
Features
Buffered Inputs
/Title (CD54H C08, CD54H CT08, CD74H C08, CD74H CT08) /Subject (High
Typical Propagation Delay: 15pF, 25oC Fanout (Over Temperature Range) Standard Outputs LSTTL Loads Driver Outputs LSTTL Loads Wide Operating Temperature Range -55oC 125oC Balanced Propagation Delay Transition Times Significant Power Reduction Compared LSTTL Logic Types Operation High Noise Immunity: 30%, Types 4.5V 5.5V Operation Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), (Min) CMOS Input Compatibility, VOL,
Ordering Information
PART NUMBER CD54HC08F3A CD54HCT08F3A CD74HC08E CD74HC08M CD74HC08M96 CD74HCT08E CD74HCT08M CD74HCT08M96 TEMP. RANGE (oC) PACKAGE CERDIP CERDIP PDIP SOIC SOIC PDIP SOIC SOIC
NOTE: When ordering, entire part number. suffix denotes tape reel.
Pinout
CD54HC08, CD54HCT08, CD74HC08, CD74HCT08 (PDIP, CERDIP, SOIC) VIEW
CAUTION: These devices sensitive electrostatic discharge. Users should follow proper Handling Procedures. Copyright
2003, Texas Instruments Incorporated
CD54HC08, CD74HC08, CD54HCT08, CD74HCT08 Functional Diagram
TRUTH TABLE INPUTS OUTPUT
High Voltage Level, Voltage Level
Logic Symbol
Logic Symbol
CD54HC08, CD74HC08, CD54HCT08, CD74HCT08
Absolute Maximum Ratings
Supply Voltage, -0.5V Input Diode Current, -0.5V 0.5V .±20mA Output Diode Current, -0.5V 0.5V .±20mA Output Source Sink Current Output Pin, -0.5V 0.5V .±25mA Ground Current, IGND .±50mA
Thermal Information
Thermal Resistance (Typical, Note (oC/W) (PDIP) Package (SOIC) Package. Maximum Junction Temperature (Hermetic Package Die) 175oC Maximum Junction Temperature (Plastic Package) 150oC Maximum Storage Temperature Range .-65oC 150oC Maximum Lead Temperature (Soldering 10s) 300oC (SOIC Lead Tips Only)
Operating Conditions
Temperature Range (TA) -55oC 125oC Supply Voltage Range, Types Types .4.5V 5.5V Input Output Voltage, Input Rise Fall Time 1000ns (Max) 4.5V. 500ns (Max) 400ns (Max)
CAUTION: Stresses above those listed "Absolute Maximum Ratings" cause permanent damage device. This stress only rating operation device these other conditions above those indicated operational sections this specification implied.
NOTE: package thermal impedance calculated accordance with JESD 51-7.
Electrical Specifications
TEST CONDITIONS PARAMETER TYPES High Level Input Voltage Level Input Voltage High Level Output Voltage CMOS Loads High Level Output Voltage Loads Level Output Voltage CMOS Loads Level Output Voltage Loads Input Leakage Current -0.02 -0.02 -0.02 -5.2 0.02 0.02 0.02 3.15 3.98 5.48 1.35 0.26 0.26 ±0.1 3.15 3.84 5.34 1.35 0.33 0.33 3.15 1.35 SYMBOL (mA) 25oC -40oC 85oC -55oC 125oC UNITS
CD54HC08, CD74HC08, CD54HCT08, CD74HCT08
Electrical Specifications
(Continued) TEST CONDITIONS PARAMETER Quiescent Device Current TYPES High Level Input Voltage Level Input Voltage High Level Output Voltage CMOS Loads High Level Output Voltage Loads Level Output Voltage CMOS Loads Level Output Voltage Loads Input Leakage Current Quiescent Device Current Additional Quiescent Device Current Input Pin: Unit Load NOTE: dual-supply systems theoretical worst case 2.4V, 5.5V) specification 1.8mA. -0.02 SYMBOL (mA) 25oC -40oC 85oC -55oC 125oC UNITS
3.98
3.84
0.02
0.26
0.33
±0.1
(Note
Input Loading Table
INPUT UNIT LOADS
NOTE: Unit Load limit specified Electrical Specifications table, e.g. 360µA 25oC.
Switching Specifications Input
PARAMETER TYPES Propagation Delay, Input Output (Figure tPLH, tPHL 50pF Propagation Delay, Data Input Output tPLH, tPHL 15pF SYMBOL TEST CONDITIONS 25oC -40oC 85oC -55oC 125oC UNITS
CD54HC08, CD74HC08, CD54HCT08, CD74HCT08
Switching Specifications Input
PARAMETER Transition Times (Figure SYMBOL tTLH, tTHL (Continued) Input Capacitance Power Dissipation Capacitance (Notes TYPES Propagation Delay, Input Output (Figure Propagation Delay, Data Input Output Transition Times (Figure Input Capacitance Power Dissipation Capacitance (Notes NOTES: used determine dynamic power consumption, gate. VCC2 (CPD where input frequency, output load capacitance, supply voltage. tPLH, tPHL tPLH, tPHL tTLH, tTHL 50pF 15pF 50pF 50pF 25oC -40oC 85oC -55oC 125oC UNITS
TEST CONDITIONS 50pF
Test Circuits Waveforms
INPUT tTLH tPHL tPLH INPUT tTHL 2.7V 1.3V 0.3V tTLH INVERTING OUTPUT tPHL tPLH 1.3V
tTHL
INVERTING OUTPUT
FIGURE TRANSITION TIMES PROPAGATION DELAY TIMES, COMBINATION LOGIC
FIGURE TRANSITION TIMES PROPAGATION DELAY TIMES, COMBINATION LOGIC
MECHANICAL
MPDI002C JANUARY 1995 REVISED DECEMBER 20002
(R-PDIP-T**)
PINS SHOWN
PLASTIC DUAL-IN-LINE PACKAGE
PINS
0.775 (19,69) 0.745 (18,92)
0.775 (19,69) 0.745 (18,92)
0.920 (23,37) 0.850 (21,59)
1.060 (26,92) 0.940 (23,88)
0.260 (6,60) 0.240 (6,10)
MS-100 VARIATION
0.070 (1,78) 0.045 (1,14)
0.045 (1,14) 0.030 (0,76)
0.020 (0,51)
0.325 (8,26) 0.300 (7,62) 0.015 (0,38) 0.200 (5,08) Seating Plane 0.125 (3,18) 0.010 (0,25) Gauge Plane
0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.010 (0,25)
0.430 (10,92)
14/18 ONLY vendor option
4040049/E 12/2002
NOTES: linear dimensions inches (millimeters). This drawing subject change without notice. Falls within JEDEC MS-001, except minimum body lrngth (Dim lead shoulder width vendor option, either half full width.
POST OFFICE 655303
DALLAS, TEXAS 75265
MECHANICAL DATA
MSOI002B JANUARY 1995 REVISED SEPTEMBER 2001
(R-PDSO-G**)
PINS SHOWN 0.050 (1,27) 0.020 (0,51) 0.014 (0,35) 0.010 (0,25)
PLASTIC SMALL-OUTLINE PACKAGE
0.244 (6,20) 0.228 (5,80) 0.157 (4,00) 0.150 (3,81)
0.008 (0,20)
Gage Plane 0.044 (1,12) 0.016 (0,40)
0.010 (0,25)
Seating Plane 0.069 (1,75) 0.010 (0,25) 0.004 (0,10) 0.004 (0,10)
PINS
0.197 (5,00) 0.189 (4,80)
0.344 (8,75) 0.337 (8,55)
0.394 (10,00) 0.386 (9,80)
4040047/E 09/01 NOTES: linear dimensions inches (millimeters). This drawing subject change without notice. Body dimensions include mold flash protrusion, exceed 0.006 (0,15). Falls within JEDEC MS-012
POST OFFICE 655303
DALLAS, TEXAS 75265
IMPORTANT NOTICE Texas Instruments Incorporated subsidiaries (TI) reserve right make corrections, modifications, enhancements, improvements, other changes products services time discontinue product service without notice. Customers should obtain latest relevant information before placing orders should verify that such information current complete. products sold subject TI's terms conditions sale supplied time order acknowledgment. warrants performance hardware products specifications applicable time sale accordance with TI's standard warranty. Testing other quality control techniques used extent deems necessary support this warranty. Except where mandated government requirements, testing parameters each product necessarily performed. assumes liability applications assistance customer product design. Customers responsible their products applications using components. minimize risks associated with customer products applications, customers should provide adequate design operating safeguards. does warrant represent that license, either express implied, granted under patent right, copyright, mask work right, other intellectual property right relating combination, machine, process which products services used. Information published regarding third-party products services does constitute license from such products services warranty endorsement thereof. such information require license from third party under patents other intellectual property third party, license from under patents other intellectual property Reproduction information data books data sheets permissible only reproduction without alteration accompanied associated warranties, conditions, limitations, notices. Reproduction this information with alteration unfair deceptive business practice. responsible liable such altered documentation. Resale products services with statements different from beyond parameters stated that product service voids express implied warranties associated product service unfair deceptive business practice. responsible liable such statements.
Mailing Address: Texas Instruments Post Office 655303 Dallas, Texas 75265
Copyright 2003, Texas Instruments Incorporated
Other recent searches
MAX2742 - MAX2742 MAX2742 Datasheet
LT1431 - LT1431 LT1431 Datasheet
GB6198 - GB6198 GB6198 Datasheet
EPC3492G - EPC3492G EPC3492G Datasheet
EPC3492G-LF - EPC3492G-LF EPC3492G-LF Datasheet
LTC4278 - LTC4278 LTC4278 Datasheet
DIR-091-033 - DIR-091-033 DIR-091-033 Datasheet
2SJ186 - 2SJ186 2SJ186 Datasheet
Privacy Policy | Disclaimer
© 2013 Datasheets.org.uk