LM158 LM258 LM358 LM2904

Datasheets.org.uk - 100 Million Datasheets from 7500 Manufacturers.

Datasheet Thumbnail

Top Searches for this datasheet

peak lm358 - peak lm358
NS LM358 - NS LM358
MARKING SMD PNP TRANSISTOR R - MARKING SMD PNP TRANSISTOR R
MARKING SMD npn TRANSISTOR R - MARKING SMD npn TRANSISTOR R
lm358 smd - lm358 smd
lm358 current monitor - lm358 current monitor
LM358 CROSS REFERENCE - LM358 CROSS REFERENCE
lm358 application note - lm358 application note
LM358 - LM358
LM2904 - LM2904
LM158 - LM158
ic lm358n - ic lm358n
LM158 - LM158
LM258 - LM258
LM358 - LM358
LM2904 - LM2904

LM158/LM258/LM358/LM2904 Power Dual Operational Amplifiers
LM158/LM258/LM358/LM2904 Power Dual Operational Amplifiers
LM158 series consists independent, high gain, internally frequency compensated operational amplifiers which were designed specifically operate from single power supply over wide range voltages. Operation from split power supplies also possible power supply current drain independent magnitude power supply voltage. Application areas include transducer amplifiers, gain blocks conventional circuits which more easily implemented single power supply systems. example, LM158 series directly operated standard power supply voltage which used digital systems will easily provide required interface electronics without requiring additional power supplies. LM358 LM2904 available chip sized package (8-Bump micro SMD) using National's micro package technology.
Advantages
internally compensated amps Eliminates need dual supplies Allows direct sensing near VOUT also goes Compatible with forms logic Power drain suitable battery operation
Features
Available 8-Bump micro chip sized package, (See AN-1112) Internally frequency compensated unity gain Large voltage gain: Wide bandwidth (unity gain): (temperature compensated) Wide power supply range: Single supply: dual supplies: 1.5V Very supply current drain (500 essentially independent supply voltage input offset voltage: Input common-mode voltage range includes ground Differential input voltage range equal power supply voltage Large output voltage swing
Unique Characteristics
linear mode input common-mode voltage range includes ground output voltage also swing ground, even though operated from only single power supply voltage. unity gain cross frequency temperature compensated. input bias current also temperature compensated.
Voltage Controlled Oscillator (VCO)
00778723
2005 National Semiconductor Corporation
DS007787
www.national.com
LM158/LM258/LM358/LM2904
Absolute Maximum Ratings (Note
Military/Aerospace specified devices required, please contact National Semiconductor Sales Office/
Distributors availability specifications.
LM158/LM258/LM358 LM158A/LM258A/LM358A Supply Voltage, Differential Input Voltage Input Voltage Power Dissipation (Note Molded Metal Small Outline Package micro Output Short-Circuit (One Amplifier) (Note 25°C Input Current (VIN -0.3V) (Note Operating Temperature Range LM358 LM258 LM158 Storage Temperature Range Lead Temperature, (Soldering, seconds) Lead Temperature, Metal (Soldering, seconds) Soldering Information Dual-In-Line Package Soldering seconds) Small Outline Package Vapor Phase seconds) Infrared seconds) 215°C 220°C 260°C 300°C 260°C +70°C -25°C +85°C -55°C +125°C -65°C +150°C Continuous 435mW -0.3V +32V
LM2904 -0.3V +26V
Continuous -40°C +85°C
-65°C +150°C 260°C 300°C
260°C 215°C 220°C
AN-450 "Surface Mounting Methods Their Effect Product Reliability" other methods soldering surface mount devices. Tolerance (Note 250V 250V
Electrical Characteristics
+5.0V, unless otherwise stated Parameter Input Offset Voltage Input Bias Current Input Offset Current Input Common-Mode Voltage Range Supply Current Conditions (Note 25°C IIN(+) IIN(-), 25°C, (Note IIN(+) IIN(-), 25°C 30V, (Note (LM2904, 26V), 25°C Over Full Temperature Range Amps (LM2904 26V) V+-1.5 V+-1.5 V+-1.5 LM158A LM358A LM158/LM258 Units
www.national.com
LM158/LM258/LM358/LM2904
Electrical Characteristics
+5.0V, unless otherwise stated Parameter Input Offset Voltage Input Bias Current Input Offset Current Input Common-Mode Voltage Range Supply Current Conditions (Note 25°C IIN(+) IIN(-), 25°C, (Note IIN(+) IIN(-), 25°C 30V, (Note (LM2904, 26V), 25°C Over Full Temperature Range Amps (LM2904 26V)
LM358 -1.5
LM2904 -1.5
Units
Electrical Characteristics
+5.0V, (Note unless otherwise stated Parameter Large Signal Voltage Gain Common-Mode Rejection Ratio Power Supply Rejection Ratio Amplifier-to-Amplifier Coupling Output Current Conditions 15V, 25°C, (For 11V) 25°C, V+-1.5V (LM2904, 26V), 25°C kHz, 25°C (Input Referred), (Note Source VIN+ VIN- 15V, 25°C Sink VIN- VIN+ 15V, 25°C, VIN- VIN+ 25°C, Short Circuit Ground Input Offset Voltage Input Offset Voltage Drift Input Offset Current Input Offset Current Drift Input Bias Current Input Common-Mode Voltage Range IIN(+) IIN(-) (Note (LM2904, 26V)
LM158A
LM358A
LM158/LM258
Units
V/mV
-120
-120
-120
25°C, (Note (Note IIN(+) IIN(-)
µV/°C
V+-2
pA/°C
V+-2
V+-2
www.national.com
LM158/LM258/LM358/LM2904
Electrical Characteristics
Parameter Large Signal Voltage Gain Output Voltage Swing Output Current +15V
(Continued) +5.0V, (Note unless otherwise stated Conditions LM158A LM358A LM158/LM258 V/mV Units
11V) +30V (LM2904, 26V) Source VIN+ +1V, VIN- 15V, Sink VIN- +1V, VIN+ 15V,
Electrical Characteristics
+5.0V, (Note unless otherwise stated Parameter Large Signal Voltage Gain Common-Mode Rejection Ratio Power Supply Rejection Ratio Amplifier-to-Amplifier Coupling Output Current Conditions 15V, 25°C, (For 11V) 25°C, V+-1.5V (LM2904, 26V), 25°C kHz, 25°C (Input Referred), (Note Source VIN+ VIN- 15V, 25°C Sink VIN- VIN+ 15V, 25°C, VIN- VIN+ 25°C, Short Circuit Ground Input Offset Voltage Input Offset Voltage Drift Input Offset Current Input Offset Current Drift Input Bias Current Input Common-Mode Voltage Range IIN(+) IIN(-) (Note (LM2904, 26V) IIN(+) IIN(-) V+-2 25°C, (Note (Note µV/°C pA/°C -120 -120 V/mV LM358 LM2904 Units
www.national.com
LM158/LM258/LM358/LM2904
Electrical Characteristics
Parameter Large Signal Voltage Gain Output Voltage Swing Output Current +15V
(Continued) +5.0V, (Note unless otherwise stated Conditions LM358 LM2904 V/mV Units
11V) +30V (LM2904, 26V) Source VIN+ +1V, VIN- 15V, Sink VIN- +1V, VIN+ 15V,
Note operating high temperatures, LM358/LM358A, LM2904 must derated based +125°C maximum junction temperature thermal resistance 120°C/W MDIP, 182°C/W Metal Can, 189°C/W Small Outline package, 230°C/W micro SMD, which applies device soldered printed circuit board, operating still ambient. LM258/LM258A LM158/LM158A derated based +150°C maximum junction temperature. dissipation total both amplifiers external resistors, where possible, allow amplifier saturate reduce power which dissipated integrated circuit. Note Short circuits from output cause excessive heating eventual destruction. When considering short cirucits ground, maximum output current approximately independent magnitude values supply voltage excess +15V, continuous short-circuits exceed power dissipation ratings cause eventual destruction. Destructive dissipation result from simultaneous shorts amplifiers. Note This input current will only exist when voltage input leads driven negative. collector-base junction input transistors becoming forward biased thereby acting input diode clamps. addition this diode action, there also lateral parasitic transistor action chip. This transistor action cause output voltages amps V+voltage level ground large overdrive) time duration that input driven negative. This destructive normal output states will re-establish when input voltage, which negative, again returns value greater than -0.3V 25°C). Note These specifications limited -55°C +125°C LM158/LM158A. With LM258/LM258A, temperature specifications limited -25°C +85°C, LM358/LM358A temperature specifications limited +70°C, LM2904 specifications limited -40°C +85°C. Note 1.4V, with from 30V; over full input common-mode range -1.5V) 25°C. LM2904, from 26V. Note direction input current input stage. This current essentially constant, independent state output loading change exists input lines. Note input common-mode voltage either input signal voltage should allowed negative more than 0.3V 25°C). upper common-mode voltage range -1.5V 25°C), either both inputs +32V without damage (+26V LM2904), independent magnitude Note proximity external components, insure that coupling originating stray capacitance between these external parts. This typically detected this type capacitance increases higher frequencies. Note Refer RETS158AX LM158A military specifications RETS158X LM158 military specifications. Note Human body model, series with
www.national.com
LM158/LM258/LM358/LM2904
Typical Performance Characteristics
Input Voltage Range Input Current
00778734
00778735
Supply Current
Voltage Gain
00778736
00778737
Open Loop Frequency Response
Common-Mode Rejection Ratio
00778738 00778739
www.national.com
LM158/LM258/LM358/LM2904
Typical Performance Characteristics
Voltage Follower Pulse Response
(Continued) Voltage Follower Pulse Response (Small Signal)
00778740
00778741
Large Signal Frequency Response
Output Characteristics Current Sourcing
00778742
00778743
Output Characteristics Current Sinking
Current Limiting
00778744
00778745
www.national.com
LM158/LM258/LM358/LM2904
Typical Performance Characteristics
Input Current (LM2902 only)
(Continued) Voltage Gain (LM2902 only)
00778746
00778747
Application Hints
LM158 series amps which operate with only single power supply voltage, have true-differential inputs, remain linear mode with input common-mode voltage VDC. These amplifiers operate over wide range power supply voltage with little change performance characteristics. 25°C amplifier operation possible down minimum supply voltage VDC. Precautions should taken insure that power supply integrated circuit never becomes reversed polarity that unit inadvertently installed backwards test socket unlimited current surge through resulting forward diode within could cause fusing internal conductors result destroyed unit. Large differential input voltages easily accomodated and, input differential voltage protection diodes needed, large input currents result from large differential input voltages. differential input voltage larger than without damaging device. Protection should provided prevent input voltages from going negative more than -0.3 25°C). input clamp diode with resistor input terminal used. reduce power supply current drain, amplifiers have class output stage small signal levels which converts class large signal mode. This allows amplifiers both source sink large output currents. Therefore both external current boost transistors used extend power capability basic amplifiers. output voltage needs raise approximately diode drop above ground bias on-chip vertical transistor output current sinking applications. applications, where load capacitively coupled output amplifier, resistor should used, from output amplifier ground increase class bias current prevent crossover distortion. Where load directly coupled, applications, there crossover distortion. Capacitive loads which applied directly output amplifier reduce loop stability margin. Values accomodated using worst-case non-inverting unity gain connection. Large closed loop gains resistive isolation should used larger load capacitance must driven amplifier. bias network LM158 establishes drain current which independent magnitude power supply voltage over range VDC. Output short circuits either ground positive power supply should short time duration. Units destroyed, result short circuit current causing metal fusing, rather large increase chip dissipation which will cause eventual failure excessive function temperatures. Putting direct short-circuits more than amplifier time will increase total power dissipation destructive levels, properly protected with external dissipation limiting resistors series with output leads amplifiers. larger value output source current which available 25°C provides larger output current capability elevated temperatures (see typical performance characteristics) than standard amp. circuits presented section typical applications emphasize operation only single power supply voltage. complementary power supplies available, standard circuits used. general, introducing pseudo-ground bias voltage reference V+/2) will allow operation above below this value single power supply systems. Many application circuits shown which take advantage wide input common-mode voltage range which includes ground. most cases, input biasing required input voltages which range ground easily accommodated.
www.national.com
LM158/LM258/LM358/LM2904
Connection Diagrams
DIP/SO Package Metal Package
00778701 00778702
View 8-Bump micro
View
00778755
View (Bump Side Down) LM358BP micro Marking Orientation LM2904IBP micro Marking Orientation
00778757 00778756
View LM358TP micro Marking Orientation
View LM2904ITP micro Marking Orientation
00778758
00778759
View
View
www.national.com
LM158/LM258/LM358/LM2904
Ordering Information
Package SO-8 Temperature Range -55°C 125°C -25°C 85°C 70°C LM358AM LM358AMX LM358M LM358MX LM358AN LM358N LM158AJ/883(Note LM158J/883(Note LM158J LM158AJLQML(Note LM158AJQMLV(Note LM158AH/883(Note LM158H/883(Note LM158AH LM158H LM158AHLQML(Note LM158AHLQMLV(Note LM258H LM358H -40°C 85°C LM2904M LM2904MX Drawing
M08A
8-Pin Molded 8-Pin Ceramic
LM2904N
N08E
J08A
TO-5, 8-Pin Metal
H08C
8-Bump micro 8-Bump micro Lead Free 14-Pin Ceramic SOIC LM158AWG/883
LM358BP LM358BPX LM358TP LM358TPX
LM2904IBP LM2904IBPX LM2904ITP LM2904ITPX
BPA08AAB 0.85 Thick TPA08AAA 0.50 Thick WG10A
Note LM158 available #5962-8771001 LM158A available #5962-8771002 Note 5962L87710 Radiation Tolerant Devices
www.national.com
LM158/LM258/LM358/LM2904
Typical Single-Supply Applications
VDC) Non-Inverting Gain Output)
00778706
00778707
needed temperature independent
Summing Amplifier (VIN'S VDC)
Power Amplifier
00778709 00778708
Where: keep
www.national.com
LM158/LM258/LM358/LM2904
Typical Single-Supply Applications
VDC) (Continued)
"BI-QUAD" Active Bandpass Filter
00778710
Fixed Current Sources
Lamp Driver
00778712
00778711
www.national.com
LM158/LM258/LM358/LM2904
Typical Single-Supply Applications
Driver
VDC) (Continued) Current Monitor
00778713
00778714
*(Increase small)
Driving
Voltage Follower
00778715
00778717
Pulse Generator
00778716
www.national.com
LM158/LM258/LM358/LM2904
Typical Single-Supply Applications
Squarewave Oscillator
VDC) (Continued) Pulse Generator
00778718
00778719
Drift Peak Detector
00778720
HIGH ZOUT
www.national.com
LM158/LM258/LM358/LM2904
Typical Single-Supply Applications
High Compliance Current Sink
VDC) (Continued) Comparator with Hysteresis
00778722
00778721
amp/volt (Increase small)
Voltage Controlled Oscillator (VCO)
00778723
*WIDE CONTROL VOLTAGE RANGE: -1.5V
www.national.com
LM158/LM258/LM358/LM2904
Typical Single-Supply Applications
VDC) (Continued)
Coupled Inverting Amplifier
00778724
Ground Referencing Differential Input Signal
00778725
www.national.com
LM158/LM258/LM358/LM2904
Typical Single-Supply Applications
VDC) (Continued)
Coupled Non-Inverting Amplifier
00778726
Shown)
Coupled Low-Pass Active Filter
00778727
www.national.com
LM158/LM258/LM358/LM2904
Typical Single-Supply Applications
VDC) (Continued)
Bandpass Active Filter
00778728
High Input Differential Amplifier
00778729
www.national.com
LM158/LM258/LM358/LM2904
Typical Single-Supply Applications
Photo Voltaic-Cell Amplifier
VDC) (Continued) Bridge Current Amplifier
00778730
00778733
High Input Adjustable-Gain Instrumentation Amplifier
00778731
www.national.com
LM158/LM258/LM358/LM2904
Typical Single-Supply Applications
VDC) (Continued)
Using Symmetrical Amplifiers Reduce Input Current (General Concept)
00778732
Schematic Diagram
(Each Amplifier)
00778703
www.national.com
LM158/LM258/LM358/LM2904
Physical Dimensions
inches (millimeters) unless otherwise noted
Metal Package Package Number H08C
Cerdip Package Package Number J08A
www.national.com
LM158/LM258/LM358/LM2904
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
SOIC Package Package Number M08A
Molded Package Package Number N08E
www.national.com
LM158/LM258/LM358/LM2904
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
Order Number LM158AWG/883 Package Number WG10A
www.national.com
LM158/LM258/LM358/LM2904
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
NOTES: UNLESS OTHERWISE SPECIFIED EPOXY COATING 63Sn/37Pb EUTECTIC BUMP RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. ESTABLISHED LOWER LEFT CORNER WITH RESPECT TEXT ORIENTATION REMAINING PINS NUMBERED COUNTERCLOCKWISE. DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE PACKAGE WIDTH, PACKAGE LENGTH PACKAGE HEIGHT. REFERENCE JEDEC REGISTRATION MO-211, VARIATION
8-Bump micro Package Number BPA08AAB 1.285 1.285 0.850
www.national.com
LM158/LM258/LM358/LM2904 Power Dual Operational Amplifiers
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
NOTES: UNLESS OTHERWISE SPECIFIED EPOXY COATING RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. ESTABLISHED LOWER LEFT CORNER WITH RESPECT TEXT ORIENTATION REMAINING PINS NUMBERED COUNTERCLOCKWISE. DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE PACKAGE WIDTH, PACKAGE LENGTH PACKAGE HEIGHT. REFERENCE JEDEC REGISTRATION MO-211, VARIATION
8-Bump micro Lead Free Package Number TPA08AAA 1.285 1.285 0.500
National does assume responsibility circuitry described, circuit patent licenses implied National reserves right time without notice change said circuitry specifications. most current product information visit www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS AUTHORIZED CRITICAL COMPONENTS LIFE SUPPORT DEVICES SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL PRESIDENT GENERAL COUNSEL NATIONAL SEMICONDUCTOR CORPORATION. used herein: Life support devices systems devices systems which, intended surgical implant into body, support sustain life, whose failure perform when properly used accordance with instructions provided labeling, reasonably expected result significant injury user. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products uses packing materials that meet provisions Customer Products Stewardship Specification (CSP-9-111C2) Banned Substances Materials Interest Specification (CSP-9-111S2) contain ``Banned Substances'' defined CSP-9-111S2. Leadfree products RoHS compliant.
National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: 180-530 Email: europe.support@nsc.com Deutsch Tel: 9508 6208 English Tel: 2171 Tel: 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560
critical component component life support device system whose failure perform reasonably expected cause failure life support device system, affect safety effectiveness.

LM158 LM258 LM358 LM2904

Top Searches for this datasheet

Other recent searches