FMce-0528

Datasheets.org.uk - 100 Million Datasheets from 7500 Manufacturers.

Datasheet Thumbnail

Top Searches for this datasheet

FMce-0528 - FMce-0528

FMce-0528 input Filters
Volt input
Nominal input, -0.5 operation with without transorb Transient rating -0.5 second throughput current over full input voltage range -0.5 Compliant MIL-STD-461C CE03 MIL-STD-461C CS01
Operating temperature -55° +125°C
attenuation kHz, typical
MIL-STD-461D, CE102 MIL-STD-461D, CS101
Compatible with MIL-STD-704 power
MODEL FMCE-0528 FMCE-0528-TR
INPUT VOLTAgE
CURRENT
Description
FMCE-0528EMI filters have been specifically designed reduce input line reflected ripple current Interpoint's MTR, MHF+, series DC/DC converters. filter used with combinations lower power converters; series converters single series converter. These filters intended volt applications which must meet MIL-STD-461C CE03 CS01 and/or MIL-STD-461D, CE102 CS101 levels conducted emissions. FMCE-0528 filters built using thick-film hybrid technology hermetically sealed metal packages military, aerospace, other high-reliability applications. Only ceramic capacitors used filters ensure reliable high temperature operation. filters offered with standard screening, "ES" screening, fully compliant "883" MIL-PRF-38534 Class screening. Standard microcircuit drawings (SMD) available.
TraNSIeNT SuppreSSIoN FMCe-0528-Tr oNLy
FMCE-0528-TR filter also features optional fast-reacting pico second) transient suppressor (transorb) which begins clamping input voltage approximately VDC, protecting DC/DC converter from damage from induced line transients. FMCE-0528 does have transorb designed those applications that require wider input voltage range
operaTINg TeMperaTure
filters rated operate, with degradation performance, over temperature range -55°C +125°C measured baseplate). Above +125°C, current must derated specified following page.
INSerTIoN LoSS
MIL-STD NoISe MaNageMeNT
resistance design results maximum power loss less than with typical input voltage.
When used conjunction with Interpoint converters, FMCE0528 FMCE-0528-TR filters reduce input ripple current within frequency band MHz. When used with Interpoint converter, performance exceeds CEO3 test MIL-STD-461C meets requirements CS01 MIL-STD-461C. These filters also meet CE102 CS101 MIL-STD-461D,
Crane Aerospace Electronics Electronics group (Interpoint Brand) www.interpoint.com
Page FMCE-0528 20100413
FMce-0528 input Filters
Volt input
Operating COnditiOns CharaCteristiCs
input Voltage range, with without transorb -0.5 -0.5 second
meChaniCal envirOnmental
size (maximum) Non-flanged 2.100 1.115 0.400 inches (53.34 28.32 10.16 case dimensions. Flanged 2.910 1.115 0.400 inches (73.91 28.32 10.16 case dimensions. Weight (maximum) grams screening
lead soldering temperature pin) storage temperature range (case) +150°C
case operating temperature (tc) +125°C full power
Derating output power/current Linearly from 100% 125°C 135°C case input output capacitance 25°c) max, case
FMCE-0528 Input filter offers Standard, 883, Class screening. Screening Tables more information.
electrostatic Discharge (esD) sensitivity Mil-prF-38534 8000
FILTER +Vin Case Output Input Common Common +Vout
isolation 25°c) megohm minimum case, except case
DC/DC CONVERTER +Vin +Vout Case Output Input Common Common
Chassis ground
Multiple units allowed rated output current filter
case ground connection between filter converter should impedance possible minimize EMI. Direct contact baseplate chassis ground provides lowest impedance.
Figure ConneCtion Diagram
Positive Input Positive Output
Input Common
Output Common
Transorb FMCE-0528-TR FMCE-0528-TR-F models only (standard, /883).
FIgure SCheMaTIC FMCe-0528 www.interpoint.com
Page FMCE-0528 20100413
FMce-0528 input Filters
Volt input
Positive Input Case ground
Designation
Positive Output Output Common Input Common
Notes pins must connected.
package indicates
BOTTOM VIEW FMCE-0528 NON-FLANGED FLANGED
Dotted line outlines flanged package option.
case case dimensions.
FIgure
www.interpoint.com
Page FMCE-0528 20100413
FMce-0528 input Filters
Volt input
MoDel nuMBering
Base Model FMCE
DsCC Drawing (5915) 10016-02HXC 10016-01HXC 10016-02HZC 10016-01HZC
Dscc nuMBers
FmCe-0528 similar Part FMCE-0528/883 FMCE-0528-TR/883 FMCE-0528-F/883 FMCE-0528-TR-F/883
Input Voltage Transorb Option (Standard FMCE-0528 transorb) designator this position) Case Option (Non-flanged case designator this position) Screening (Standard screening designator this position.)
Output Current
Models with "TR" have transorb (-01 DSCC numbers). exact specifications DSCC product, refer DSCC drawing. DSCC drawings downloaded from: http://www. dscc.dla.mil/programs/smcr
lines below, enter seleCtion From unDer eaCh Category Determine moDel number.
MoDel selection
category
FMce-0528
Base MoDel input Voltage "FMce-0528" only available selection
transorB option transorB leave blank) (with transorb)
case/leaD option (non-FlangeD leave blank) (flanged)
screening standard (leave blank) (class QMl)
selection
Transorb Option: standard filter transorb) leave transorb option blank. filter with transorb, insert letters Option position. Case Options: standard case, case leave case option blank. flanged case option, case insert letter Case Option position. Screening: standard screening leave screening option blank. other screening options, insert desired screening level. more information Screening Tables
www.interpoint.com
Page FMCE-0528 20100413
FMce-0528 input Filters
Volt input
Electrical Characteristics: -55° +125°C nominal Vin, unless otherwise specified.
MODEL
paraMeTer INpuT VoLTage INpuT CLaMpINg VoLTage NoISe reJeCTIoN reSISTaNCe (rDC) CapaCITaNCe MaXIMuM CurreNT CoNDITIoNS CoNTINuouS TraNSIeNT, -55°C +125°C 25°C +125°C CaSe 25°C STeaDy STaTe 25°C
FMCE-0528-TR
-0.5 -0.5 40.8 44.7 44.7 45.1 47.0 49.5 0.110 44,000 49.4 49.4 54.2 0.125 0.150 48,000 -0.5 -0.5
FMCE-0528
0.110 44,000 0.125 0.150 48,000 uNITS
ouTpuT VoLTage ouTpuT CurreNT poWer DISSIpaTIoN MaXIMuM CurreNT
VOUT (RDC)
VOUT (RDC)
STeaDy STaTe -0.5 125°C 25°C
Notes guaranteed design, tested. FMCE-0528 does have transorb does clamp input voltage
source impedance Typical applications result Vout within Vin.
www.interpoint.com
Page FMCE-0528 20100413
FMce-0528 input Filters
Volt input
Typical Performance Curves: 25°C nominal Vin, unless otherwise specified.
MIL-STD-461C POWER LIMITS
EMISSION LEVEL
.015
EMISSION LEVEL
.015
NARROWBAND
MIL-STD-461C POWER LIMITS
NARROWBAND
FREQUENCY (MHz)
FREQUENCY (MHz)
High power DC/DC converter without filtering.
FIgure
CE03: High power DC/DC converter filtered with FMCE-0528
FIgure
EMISSION LEVEL
imit
FREQUENCY (MHz)
CE102: High power converter filtered with FMCE-0528.
FIgure
IMPEDANCE (OHMS)
FREQUENCY (kHz)
ATTENUATION (dB)
FREQUENCY (kHz)
FMCE-0528 Output Impedance (measured output with input pins shorted)
FMCE-0528 Attenuation
FIgure www.interpoint.com
FIgure
Page FMCE-0528 20100413
FMce-0528 input Filters
Volt input
BOTTOM VIEW CASE
Seam Seal
0.040 (1.02)
1.115 max. (28.32)
Squared corner case indicate one.
0.955 (24.26)
0.555 (14.1)
0.155 (3.94) 0.000 0.400 max. (10.16) 0.000 0.25 ±0.01 (6.4 ±0.3) 0.000
0.245 (6.22)
1.845 (46.86)
Seal hole: 0.120 ±0.002 (3.05 ±0.05)
Case dimensions inches (mm) Tolerance ±0.005 (0.13) three decimal places ±0.01 (0.3) decimal places unless otherwise specified CAUTION Heat from reflow wave soldering damage device. Solder pins individually with heat application exceeding 300°C seconds pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins alloy/Gold, ceramic seal Seal hole 0.120 ±0.002 (2.34 0.05)
Case Filters, 20100316 Please refer numerical dimensions accuracy. information believed accurate, responsibility assumed errors omissions. Interpoint reserves right make changes products specifications without notice. Copyright 1999-2009 Interpoint Corp. rights reserved.
FIgure CaSe
www.interpoint.com
Page FMCE-0528 20100413
2.100 max. (53.34)
FMce-0528 input Filters
Volt input
BOTTOM VIEW CASE Flanged cases: Designator required Case Option position model number.
Seam Seal
0.040 (1.02)
1.115 max. (28.32)
case indicates
0.955 (24.26) 0.555 (14.1) 0.162 (4.11)
0.155 (3.94) 0.000
0.245 (6.22)
1.845 (46.86)
2.090 (53.01)
0.230 (5.84)
2.910 (73.91)
Flange thickness: 0.060 (1.52)
Case dimensions inches (mm) Tolerance ±0.005 (0.13) three decimal places ±0.01 (0.3) decimal places unless otherwise specified CAUTION Heat from reflow wave soldering damage device. Solder pins individually with heat application exceeding 300°C seconds pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins alloy/Gold, cceramic seal. Seal Hole: 0.120 ±0.002 (3.04 ±0.05) Case 20091111 Please refer numerical dimensions accuracy. information believed accurate, responsibility assumed errors omissions. Interpoint reserves right make changes products specifications without notice. Copyright 1999-2009 Interpoint Corp. rights reserved.
FIgure CaSe
www.interpoint.com
Page FMCE-0528 20100413
2.320 (58.93)
0.400 max. (10.16)
0.000
0.25 ±0.03 (6.4 ±0.8)
0.000
FMce-0528 input Filters
Volt input
STANDARD (NON-QML) /883 (CLASS QML) PRODUCT ELEMENT EVALUATION
COmpOnent-level test perFOrmed
standard nOn-Qml
/883 Class
Element Electrical (probe) Element Visual Internal Visual Final Electrical Wire Bond Evaluation
SLAMTM/C-SAM: Input capacitors only (Add'l test, req.
Notes: Standard /ES, non-QML products, meet requirements MIL-PRF-38534. Active components (Microcircuit Semiconductor Die) Passive components applicable filters that have wire bonds. Definitions: Element Evaluation: Component testing/screening MIL-STD-883 determined MIL-PRF-38534 SLAMTM: Scanning Laser Acoustic Microscopy C-SAM: Mode Scanning Acoustic Microscopy
SCreeNINg TabLe eLeMeNT eVaLuaTIoN
www.interpoint.com
Page FMCE-0528 20100413
FMce-0528 input Filters
Volt input
STANDARD (NON-QML) /883 (CLASS QML) PRODUCT ENVIRONMENTAL SCREENING
test perFOrmed Pre-cap Inspection Method 2017, 2032 Temperature Cycle times) Method 1010, Cond. -65°C 150°C, ambient Method 1010, Cond. -55°C 125°C, ambient Constant Acceleration Method 2001, 3000 Method 2001, Burn-in Method 1015, 125°C case, typical hours hours Final Electrical Test MIL-PRF-38534, Group Subgroups through -55°C, +25°C, +125°C case Subgroups +25°C case Hermeticity Test Fine Leak, Method 1014, Cond. Gross Leak, Method 1014, Cond. Gross Leak, 10-3) Final visual inspection Method 2009
Test methods referenced MIL-STD-883 determined MIL-PRF-38534. Notes: Standard /ES, non-QML products, meet requirements MIL-PRF-38534. Burn-in temperature designed bring case temperature +125°C
125°C standard nOn-Qml1
125°C nOn-Qml1
/883 Class
SCreeNINg TabLe eNVIroNMeNTaL SCreeNINg
FMCE-0528 Input Filters FMCE-0528 20100413. This revision supersedes previous releases. technical information believed accurate, responsibility assumed errors omissions. Interpoint reserves right make changes products specifications without notice. FMCE-0528 Series trademark Interpoint. Copyright 1999 2010 Interpoint Corporation. rights reserved. www.interpoint.
Page

FMce-0528

Top Searches for this datasheet

Other recent searches