APW7071
|
|
|
Top Searches for this datasheet
APW7071 - APW7071
APW7071
Step-Up Converter Series White LEDs Driver
Input Voltage Range 400mA Internal Switch Current 1MHz Switching Frequency 70µA Typical Load Quiescent Current 0.1µA Typical Shutdown Current Internal Soft-Start Efficiency Operating Output Capacitor Down 0.1µF Over Voltage Protection Included Lead Free Green Devices Available (RoHS Compliant)
General Description
APW7071 high frequency step-up DC/DC converter small 6-lead SOT-23 package specially designed drive white LEDs with constant current. device drive LEDs series from Li-Ion cell. APW7071 ideal panels requiring current high efficiency well white applications cellular phone back-lighting.
Configuration
Applications
Cellar Phones White Back Light PDAs, Handheld Computers Digital Still Cameras Players Receivers
SOT-23-6 (Top View)
Ordering Marking Information
APW7071 Assembly Material Handling Code Temperature Range Package Code Package Code SOT-23-6 Operating Ambient Temperature Range 85oC Handling Code Tape Reel Assembly Material Lead Free Device Halogen Lead Free Device Date Code
APW7071C
W71X
Note: ANPEC lead-free products contain molding compounds/die attach materials 100% matte plate termination finish; which fully compliant with RoHS. ANPEC lead-free products meet exceed lead-free requirements IPC/JEDEC J-STD-020C classification lead-free peak reflow temperature. ANPEC defines "Green" mean lead-free (RoHS compliant) halogen free does exceed 900ppm weight homogeneous material total does exceed 1500ppm weight). ANPEC reserves right make changes improve reliability manufacturability without notice, advise customers obtain latest version relevant information verify before placing orders. Copyright ANPEC Electronics Corp. Rev. Jul., 2008 www.anpec.com.tw
APW7071
Absolute Maximum Ratings
Symbol Input Supply Voltage Voltage Pins SHDN VOVP TSTG TSDR Voltage Switch Voltage Junction Temperature Range Storage Temperature Range Maximum Lead Soldering Temperature, Seconds
(Note
Rating -0.3 -0.3 VIN+0.3 -0.3 -0.3 ~150 Unit
Parameter
Note Absolute Maximum Ratings those values beyond which life device impaired. Exposure absolute maximum rating conditions extended periods affect device reliability.
Thermal Characteristics
Symbol Parameter Junction-to-Ambient Resistance Free
(Note
Typical Value
Unit °C/W
Note measured with component mounted high effective thermal conductivity test board free air.
Recommended Operating Conditions
Symbol VOUT COUT Input Supply Voltage Switch Voltage Output Voltage Inductor Input Capacitor Output Capacitor Operating Ambient Temperature Operating Junction Temperature Parameter
(Note
Value Unit Min. Typ. Max.
Note Please refer Typical Application Circuit
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Electrical Characteristics
VIN=3.3V, SHDN=VIN, -40°C +85°C, typical values TA=+25°C (unless otherwise noted).
APW7071 Symbol Parameter Test Conditions Min. SUPPLY VOLTAGE CURRENT IQ_SD UVLO Input Voltage Range Operating Quiescent Current Shutdown Current Under-Voltage Lockout Threshold Under-Voltage Lockout Hysteresis ENABLE SHDN High Level Input Voltage SHDN Level Input Voltage SHDN Input Leakage Current SHDN=GND IOUT=0, switching, VFB=0.3V SHDN=GND Typ. Max. Unit
POWER SWITCH CURRENT LIMIT toff Rdson Maximum Switching Voltage Minimum Off-Time Maximum On-Time MOSFET On-Resistance MOSFET Leakage Current ILIM OUTPUT VOUT VREF Adjustable Output Voltage Range Feedback Input Bias Current Feedback Trip Point Voltage Threshold Hysteresis IOVP Input Current Leakage Current VOVP=15V SHDN=GND, VOVP=6V VFB=1.3V 2.5VIN6.0V 0.237 0.25 0.263 18.5 MOSFET Current Limit VIN=2.5V, =200mA =19V 1000
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Typical Operating Characteristics
(Circuit Figure 3.3V, ILED 20mA, 4.7µH, 4.7µF, COUT 0.1µF,4 LEDs, +25°C, unless otherwise noted.) Efficiency Current
VIN=4.2V VIN=3.6V
Efficiency Supply Voltage
Efficiency(%)
Efficiency(%)
VIN=2.7V
ILED=15mA
Current(mA)
Supply Voltage
Switch Resistance Supply Voltage
Switch Resistance Junction Temperature
Swiitch Resistaance
Switch Resistance
VIN=3.3V
Supply Voltage
Junction Temperature (°C)
No-Switching Quiescent Current Supply Voltage
Current Supply Voltage
No-Switching Quiescent Current (µA)
Current (mA)
L=4.7µH COUT=0.1µF LEDs
Supply Voltage Copyright ANPEC Electronics Corp. Rev. Jul., 2008
Supply Voltage www.anpec.com.tw
APW7071
Operating Waveforms
(Circuit Figure 3.3V, ILED 20mA, 4.7µH, 4.7µF, COUT 0.1µF,4 LEDs, +25°C, unless otherwise noted.) Start-up Waveform
VSHDN
Waveform
VOUT
VOUT
CH1: VSHDN, 2V/Div, CH2: VOUT, 5V/Div, CH3: IIN, 100mA/Div, Time: 1ms/Div
CH1: VOUT, 5V/Div, Time: 20ms/Div
Operation
Pulse Burst Operation
CH1: VOUT, 200mV/Div, CH2: VSW, 10V/Div, CH3: VFB, 100mA/Div, Time: 1µs/Div
CH1: VOUT, 200mV/Div, CH2: VSW, 10V/Div, CH3: VFB, 100mA/Div, Time: 2µs/Div
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Description
NAME SHDN FUNCTION Switch Pin. Connect this inductor/diode here. Ground Pin. Feedback Pin. Reference voltage 0.25V. Connect this cathode lowest resistor (RFB). Calculate resistor value according 0.25V/lLED Shutdown Pin. Pulling this ground forces device into shutdown mode reducing supply current less than 1µA. This should left floating. Over voltage protection sense pin. Connect this output capacitor. Left unconnected disable function. Supply voltage Pin.
Block Diagram
Under Voltage Lockout 400ns Min. off-time SHDN Comparator
Error Comparator
VREF=0.25V
Control Logic
Gate Driver
N-MOSFET
Max. on-time
Current Limit RSENSE
SHDN
Soft start
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Typical Application Circuits
2.7V~6V 4.7µF
4.7µH
MSCD052
VOUT
0.1µF
SHDN
Figure.1 Typical LEDs application Using more output capacitors with larger capacitance like reduce ripple current well improve line regulation.
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Function Description
Operation APW7071 operates pulse frequency modulation (PFM) scheme with constant peak current control. operation understood referring Block Diagram. converter keeps monitoring output voltage through resistor-divider connected with GND, VOUT. When feedback voltage falls below reference voltage (typical 0.25V), internal switch turns inductor current ramps switch turns inductor current reaches internal peak current limit (400mA typical). second criterion that turns switch maximum on-time control. switch off, external Schottky diode forwards bias, that current delivered output. switch remains minimum 400ns (typical), wouldn' turned again until feedback voltage drops below reference voltage. This regulation scheme allows wider selection range inductor output capacitor. Shutdown Driving SHDN ground places shutdown. When shutdown, internal power MOSFET turns off, internal circuitry shuts down quiescent supply current reduces <0.1µA (typical). Soft-Start APW7071 limits this inrush current increasing current limit start-up. Under Voltage Lockout Transients cause system damage failure when powering undergoing instantaneous glitches supply voltage. Then, undervoltage lockout circuit turns main switch prevent malfunction input voltage. Over Voltage Protection driving applications, feedback voltage falls down LEDs, series, failed. Meanwhile, converter unceasingly boosts output voltage like open-loop operation. Therefore, overvoltage protection (OVP), monitoring output voltage pin, integrated into chip prevent output voltages from exceeding their maximum voltage ratings. When voltage rises above threshold (17V typical), converter stops switching prevents output voltage from rising. converter work again when voltage falls below voltage threshold.
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Application Information
Setting LEDs Current figure converter regulates voltage pin, connected with cathod lowest current-sense resistor 0.25V(typical). Therefore, current (ILED), flowing LEDs calculated following equation:
ILED 0.25V
Using signal apply SHDN external signal applied SHDN cyclically turns converter. average current through LEDs will increase proportionally duty cycle signal. soft-start duration, signal with frequency from 100Hz 300Hz recommended.
2.7V~6V 4.7µF 4.7µH 0.1µF 100Hz~300Hz brightness control MSCD052 VOUT
Brightness Control brightness LEDs controlled adjusting current. There three following recommended methods adjust brightness LEDs Using adjustable voltage applied shown figure. figure additional network connected between junction cathode adjustable voltage (VADJ), connected with injects constant current (I1, I1=(VADJ-0.25V)/R3) into node when voltage regulated 0.25V. Therefore, voltage across reduced offset voltage (I1xR2), reducing current brightness. current calculated following equation: 0.25V VADJ 0.25
SHDN
Duty=100%, LED=20mA Duty=0%,
Figure. Brightness Control applying signal SHDN Using filtered signal figure. brightness control achieved applying signal filter generate filtered signal instead VADJ. signal with frequency above 5kHz recommended.
2.7V~6V 4.7µF 4.7µH 0.1µF MSCD052 VOUT
ILED
With VADJ from 3.3V, current controlled from 20mA.
2.7V~6V 4.7µF 4.7µH 0.1µF MSCD052 VOUT
SHDN
120K
0.1uF
3.3V brightness control Duty=100%, Duty=0%, LED=20mA
SHDN
120K
Figure. Brightness Control filtered signal
Inductor Selection inductor together with load current (IOUT), internal peak current (IPK), input (VIN) output voltage (VOUT) application determines switching frequency
VADJ=3.3V, VADJ=0V, LED=20mA
Figure. Brightness Control adjustable voltage
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Application Information (Cont.)
Inductor Selection (Cont.) converter. switching frequency calculated
IOUT (VOUT
Recommended inductors
Part LQH31CN2R2M03L LQH32CN4R7M23L SH30184R7YSB LQH32CN100K53L SH3018100YSB Value (µH) Vendor Murata Murata Murata
where foward voltage Schottky diode.
Output capacitor selection smaller inductor gets higher switching frequency lower efficiency. operate under discontinuous conduction mode, inductor selected below:
TOFF,MIN (VOUT
better output voltage filtering, output capacitor like ceramic capacitors recommended. selection output capacitance directly influences output voltage ripple converter. output voltage ripple calculated
VOUT IOUT VOUT
white applications, inductor values between recommended. inductor also affects maximum output power. maximum output current calculated
IOUT ,MAX TOFF IIN,AVG VOUT VOUT
white applications, output ripple proportional current. proper output capacitor from 0.1µF recommended limit maximum current ripple current. Recommended output capacitor
where
TOFF
VOUT
Part GRM188R61E105KA12
Value 1.0µF/X5R/0603/25V 0.22µF 0.1µF
Vender Murata
OFF,
0.4µs (typical)
understood following figure.
Input capacitor selection good input voltage filtering, ceramic capacitors recommended. 4.7µF ceramic input capacitor sufficient most applications. better-input voltage filtering capacitor value increased. Recommended input capacitor
Part Value 4.7µF/X5R/0603/6.3V 10µF/X5R/0805/6.3V Vender Murata Murata GRM188R60J475KE19D GRM219R60J106KE19D
Toff Toff,min
Figure.5 Discontinuous Conduction Mode Operation Waveform efficiency estimated section "Typical Operating Characteristics".
Diode selection achieve high efficiency, Schottky diode must used. current rating diode must meet peak current rating converter.
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Application Information (Cont.)
Diode selection (Cont.) Recommended diode
Part MSCD052 Reverse Voltage Vender Zowie
Layout consideration switching power supplies especially with high peak currents switching frequency, layout important step design. layout carefully done, regulator show noise problems duty cycle jitter. 1.The input capacitor must placed close device, which reduce copper trace resistance effect input ripple 2.The inductor diode should placed close possible switch minimize switching noise. 3.The feedback feedback network should away from inductor shielded ground plane trace minimize noise.
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Package Information
SOT-23-6
VIEW
0.25
GAUGE PLANE SEATING PLANE VIEW SOT-23-6 INCHES MIN. MAX. 0.057 0.000 0.035 0.012 0.003 0.106 0.102 0.055 0.037 0.075 0.60 0.012 0.024 0.006 0.051 0.020 0.009 0.122 0.118 0.071 MAX. 1.45 0.15 1.30 0.50 0.22 3.10 3.00 1.80
MILLIMETERS MIN.
0.00 0.90 0.30 0.08 2.70 2.60 1.40 0.95 1.90 0.30
Note Follow JEDEC TO-178 Dimension include mold flash, protrusions gate burrs. Mold flash, protrusion gate burrs shall exceed side.
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Carrier Tape Reel Dimensions
SECTION SECTION
Application
178.0± 2.00 MIN. SOT-23-6 4.0± 0.10 4.0± 0.10
8.4+2.00 13.0+0.50 MIN. -0.00 -0.20 1.5+0.10 2.0± 0.05 MIN. -0.00
20.2 MIN.
3.5± 0.05
8.0± 0.30 1.75± 0.10
0.6+0.00 3.20± 0.20 3.10± 0.20 1.50± 0.20 -0.40 (mm)
Cover Tape Dimensions
Package Type SOT-23-6 Unit Tape Reel Quantity 3000
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
APW7071
Reflow Condition
(IR/Convection Reflow)
Critical Zone Ramp-up
Temperature
Tsmax
Tsmin Ramp-down Preheat
25°C Peak
Reliability Test Program
Test item SOLDERABILITY HOLT Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B, A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD
Time
Description 245°C, 1000 Bias @125°C Hrs, 100%RH, 121°C -65°C~150°C, Cycles VHBM 2KV, 200V 10ms, 100mA
Classification Reflow Profiles
Profile Feature Average ramp-up rate Preheat Temperature (Tsmin) Temperature (Tsmax) Time (min max) (ts) Time maintained above: Temperature (TL) Time (tL) Peak/Classification Temperature (Tp) Time within actual Peak Temperature (tp) Ramp-down Rate Time 25°C Peak Temperature Sn-Pb Eutectic Assembly 3°C/second max. 100°C 150°C 60-120 seconds 183°C 60-150 seconds table 10-30 seconds 6°C/second max. minutes max. Pb-Free Assembly 3°C/second max. 150°C 200°C 60-180 seconds 217°C 60-150 seconds table 20-40 seconds 6°C/second max. minutes max.
Notes: temperatures refer topside package. Measured body surface.
Copyright ANPEC Electronics Corp. Rev. Jul., 2008 www.anpec.com.tw
APW7071
Classification Reflow Profiles (Cont.)
Table SnPb Eutectic Process Package Peak Reflow Temperatures Package Thickness <2.5 Volume <350 +0/-5°C +0/-5°C
Volume +0/-5°C +0/-5°C
Table Pb-free Process Package Classification Reflow Temperatures Volume Volume Volume <350 350-2000 >2000 <1.6 +0°C* +0°C* +0°C* +0°C* +0°C* +0°C* +0°C* +0°C* +0°C* Tolerance: device manufacturer/supplier shall assure process compatibility including stated classification temperature (this means Peak reflow temperature +0°C. example 260°C+0°C) rated level. Package Thickness
Customer Service
Anpec Electronics Corp. Head Office No.6, Dusing Road, SBIP, Hsin-Chu, Taiwan, R.O.C. 886-3-5642000 886-3-5642050 Taipei Branch Lane 218, Jhongsing Rd., Sindian City, Taipei County 23146, Taiwan 886-2-2910-3838 886-2-2917-3838
Copyright ANPEC Electronics Corp. Rev. Jul., 2008
www.anpec.com.tw
Other recent searches
Tsi500 - Tsi500 Tsi500 Datasheet
TPS100LBP - TPS100LBP TPS100LBP Datasheet
SOT490 - SOT490 SOT490 Datasheet
IDT54 - IDT54 IDT54 Datasheet
74FCT16374T - 74FCT16374T 74FCT16374T Datasheet
CN0603S17BHTG - CN0603S17BHTG CN0603S17BHTG Datasheet
CD4504B - CD4504B CD4504B Datasheet
1599220000 - 1599220000 1599220000 Datasheet
Privacy Policy | Disclaimer
© 2013 Datasheets.org.uk